Answer: 12 hours
Explanation: We use a fast seal with quick dry additives added …. |
| Cross Roads Paving LLc |
Answer: 24 hours
Explanation: Need to adhere to the driveway or parking lot for 24 hours before drive on |
| Denton's sealcoating |
Answer: 12 hours
Explanation: Debends on sunlight and Long as the temperature is 60 and rising overnight will be fine, shady places may take a little longer. |
| Gold Coast Grading and Paving |
|
| ProMatcher |
Answer: 24 hours
Explanation: It really depends on the time of day. If we spray in the morning, you could drive on it in the evening |
| WAMCO Asphalt Maintenance |
Answer: 12 hours
Explanation: It all Depends on the weather for much hotter where you Would-be able to go on a lot sooner if it's colder weather it might take a little bit longer |
| A & J's Sealcoating |
Answer: 24 hours
Explanation: usually a few hours for foot traffic
24 hours for cars etc. |
| Dumor Construction Inc |
|
| ProMatcher |
Answer: 12 hours
Explanation: In most cases asphalt sealer will dry in a few hours,but we recommend to stay off of it for 12 hours to ensure that it is fully cured out. |
| TRUESTRONG Paving co |
Answer: 24 hours
Explanation: Dries to walk on within two hours for traffic ready in 24 fore asphalt to harden |
| Patgormansealcoating |
Answer: 24 hours
Explanation: For best results wait 24 hours before driving on the fresh sealant |
| Prestigious Asphalt & Concrete llc |
|
| ProMatcher |
Answer: 24 hours
Explanation: On a good sunny day 24 hours will be plenty of time to let the sealer cure. In the early spring and fall however it may take up to 48 hours to fully cure. |
| CPR Asphalt Maintenance |
Answer: 72 hours
Explanation: It is recommended you keep any vehicles from driving on it for 48-72 hrs after applied. However, in most cases it is usually ok to walk on it 24 hrs after applied. |
| Texas Precision Paving, LLC |
Answer: 24 hours
Explanation: Temperature and rain can play a part. Best if it's above 55 degrees. |
| Saul Reyes Contracting. |
|
| ProMatcher |
Answer: 12 hours
Explanation: 12 hours is plenty of time for the driveway to dry. |
| Aj and son asphalt specialist |
Answer: 24 hours
Explanation: 24 hrs is required |
| True Seal |
Answer: 12 hours
Explanation: 12 hours if one has to use their drive, but recommend 24 hours. |
| Clay Campbell Pavement Maintenance |
|
| ProMatcher |
Answer: 12 hours
Explanation: Depending on the current temperature 70 deg.+ the sealer we use can be walked on in about 3 hours and can be driven on in about 6 hours. However we recommend 12 to 24 hours to maintain a great looking finish. |
| Southern Utah Sealcoating LLC |
Answer: 24 hours
Explanation: Most. Driveways can. Be. Drove. On. In 24. Hrs. Our. Company uses a. Additional. Dryer. Called. Fass. Dry. It. A. Commerical. Additive. Designed. For. Parking. Lots. Which. Speeds. Up. Drying. Timep |
| NICHOLS ASPHALT |
Answer: 24 hours
Explanation: 24 hours in most cases, if you have shaded areas of if the temp. Drops below 50 degrees over night curing time will be longer. |
| PC Paving Llc. |
|
| ProMatcher |
Answer: 24 hours
Explanation: Or until all the visible wet spots are gone. Will take a little longer in shaded areas. |
| West Paving |
Answer: 48 hours
Explanation: During the summer months of May through August we recommend staying off the driveway with vehicles for 48 hours. After September 1st allow 72 hours or more depending on the temperature. Driveway sealer will dry like paint from the top down. It may feel dry on the surface but may still be wet underneath. You can walk on the driveway as soon as it feels dry to the touch, usually just a few hours in sunny areas. Allow additional time for shady areas at all times. |
| rons concrete & asphalt tearout |
Answer: 24 hours
Explanation: We recommend 24 hours to insure it's completely dry. |
| J.W. Smith Paving |
|
| ProMatcher |
Answer: 24 hours
Explanation: A full cure takes a temp of at least 53 and rising. And at least 24 hours to fully cure |
| Mullins Asphalt Paving |
Answer: 24 hours
Explanation: 24 hours allows the sealer to cure. |
| Chance 2 Sealcoat |
Answer: 24 hours
Explanation: Every manufacturer has difference specifications on how long, once sealer is applied, you are able to drive over. A majority of sealers require a minimum of 24 hours, once sealer is applied, you will be able to drive over- if and only if conditions meet manufacturer recommendations. |
| Veile Contracting Inc |
|
| ProMatcher |
Answer: 24 hours
Explanation: Most are 24 hours refer to the lable |
| Rowland Exterior Solutions |
Answer: 24 hours
Explanation: Usually 24 hours is sufficient, but it can be quicker if an accelerator is used in the sealer product for certain jobs. |
| United Paving Company |
Answer: Not sure
Explanation: Not my expertise |
| American roofing &remodeling |
|
| ProMatcher |
Answer: 24 hours
Explanation: That ways for it to dry all of it take 24 hours |
| Metlow Roofing |
Answer: 48 hours
Explanation: I always say 24-48 hours or until sealant is not tacky to the touch depends on weather |
| Greener Touch Landscaping llc |
Answer: 12 hours
Explanation: Will take less time in warmer weather. |
| Mr blacktop |
|
| ProMatcher |